厦门昕钢防腐工程科技有限公司-不锈钢专用纳米防锈清漆

当前位置:首页 > 产品展示 > 涂料
  • 1
  • 不锈钢专用纳米防锈清漆
产品名称:不锈钢专用纳米防锈清漆
产品介绍

产品简介 / DESCRIPTION:

由特殊树脂及纳米防腐颜填料、助剂、少量溶剂等组成

Composed of special resin and NANO anticorrosive pigments


产品特性 / CHARACTERISTICS:

对不锈钢基材附着力良好,大大提高不锈钢基材在极端恶劣腐蚀环境下的抗腐蚀性能。优秀的耐候性和保光性,极好的耐冲击和耐磨损性能,漆膜表面能低,耐污性好。耐低温可达‐200℃

Good adhesion to stainless steel, greatly improve the corrosion resistance of stainless steel in the extreme corrosive environment. Excellent weather resistance and  light resistance, excellent impact resistance and abrasion resistance paint film with low surface energy and good antifouling effect. Low temperature resistance down to

‐200℃


推荐用途 / RECOMMENDED USES:

适用于不锈钢基材,尤其是经过电化学处理后。施工性能好,容易上厚度,方便修补,重涂性好

For stainless steel substrate, especially after electrochemical treatment, easy to apply for thickness, easy to repair paint with good re‐coating


注意事项 / NOTE:

安科纳米防锈清漆对水和潮气敏感,会缩短适用期

The Anke Nano Anti‐corrosion varnish is sensitive to water and moisture, which will lead to shorten of pot life

底材 / SUBSTRATES:

适用于不锈钢基材。对经过电化学处理后的不锈钢光滑表面,不需要打磨即可兼容性良好。其他金属底材需要试验验证附着力

May be used over stainless steel substrate, especially good compatibility with the electrochemical treated stainless steel Smooth and compact surface, without sanding. Other metal substrates need to test the adhesion


面漆要求 / TOPCOAT REQUIRED:

一般不需要

Normally none

3.jpg

体积固含 / SOLIDS CONTENT:

50 ±2% by volume


表面处理 / SURFACE PREPARATION:

1.使用清水冲去不锈钢表面盐份及其它水溶性污物

2.对于一般不锈钢基材可以用适当砂纸打磨增强附着力, 对于结果电化学处理的不锈钢基材不需打磨以免损伤电化学保护膜

3.用工业酒精擦拭表面并晾干以保证表面清洁干燥

1.Remove any salt or other Water soluble contaminants by clean water from the stainless steel

2.For the general stainless steel substrate can be polished with appropriate sandpaper to enhance the adhesion, for stainless steel with electrochemical processing shall NOT be polished so as not to damage the electrochemical film

3.wipe the surface with industrial alcohol and dry to keep

the surface clean and dry before apply


钢材表面 / STEEL:

用在洁净、干燥的不锈钢基材之上

Apply over clean, dry stainless steel


混合 / MIXING:

各组分搅拌均匀,再将两组分按 A 组分:B 组分=1:1

(质量比)=1:1(体积比)混合,并搅拌均匀

Mix Part A and Part B separately and combine in the following proportions; Part A : Part B = 1:1 by mass, 1:1 by volume


稀释/ THINNING:

用专用稀释剂PS1003稀释。不得使用其他稀释剂

With special Thinner PS1003. Can NOT use other thinner


清洗 / CLEAN UP:

稀释剂PS1003

4.jpg

无气喷涂参数 / APPLICATION METHODS:

喷嘴孔径 / Nozzle:0.013 ‐ 0.019" 喷嘴压力 / Pressure:100‐120 kg/cm2

推荐采用刷涂。Brush apply is recommended

5.jpg

底材表面温度应比空气露点至少高3℃,否则不能施工。 Do not apply when the surface temperature is less than 3 ℃ above the dew point of the air

6.jpg

储存期/SHEL FLIFE:

油漆:1 ‐ 3 年/ Party A: 1 ‐ 3 years。

固化剂:9   个月/   Hardener   Party   B:   9   months。(取决于储存的环境/ Depends On Storage Condition )


包装规格/ PACKING:

A 组分/B 组分:1kg/1kg 稀释剂:0.8kg